Sigma C4 Uživatelský manuál Strana 116
- Strana / 120
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
116
C4 Manual Rev 7.5.2
WP Set PID constants ............................................ 67
PN Select active (control) probe ....................................... 70
Ports............................................................. 10
Aux/power control port control ..................................... 52
connector ...................................................... 22
Cryogenic boost control ........................................... 52
EIA-232 ....................................................... 55
IEEE488 (GPIB) ................................................ 55
Outputs and input, installation and use ............................. 98
Refrigeration compressor control ................................... 52
TO & TF Turn aux/power control port on & off........................ 72
TTL ........................................................ 52, 98
Power
2nd power cords WARNING ...................................... 101
Disconnecting.................................................. 101
Probe
Number of probes................................................ 82
PN Select active (control) probe .................................... 70
Probe correction (software probe calibration).......................... 83
Specifying active (control) probe for program.......................... 43
Probe 2
No probe 2 error .............................................. 49, 50
Probe averaging.................................................... 35
Probe connections .................................................. 22
Probe correction (calibration) ...................................... 32, 80
Entering probe correction setup data ................................ 84
SC Set probe correction ........................................... 66
Probe out of range shutdown ......................................... 29
Clearing ....................................................... 30
Effect of probe correction.......................................... 30
Error/Status String reporting ...................................... 30
Probes, number installed, defining .................................... 79
Program
Aux/power control port control ..................................... 52
Displaying step number while running .............................. 49
Interrupting/restarting ........................................... 48
Looping ........................................................ 51
Looping forever ................................................. 49
Pre-read Errors ................................................. 49
Refrigeration compressor control ................................... 52
Running (executing) .............................................. 48
Program memory, clearing ........................................... 46
Program mode .................................................. 10, 43
Control/program example(s) ....................................... 87
- SIGMA SYSTEMS 1
- MODELS C4 & CC-3 1
- TABLE OF CONTENTS 3
- 1. INTRODUCTION 9
- C4 Manual Rev 7.5.2 10
- 1.5.3 Firmware Uploads 13
- ***-**** 19
- 2.1.3 Mode Switch 20
- 200 - 100c 392 - 148f 23
- 4-0 3276 24
- Starting the upload on the C4 27
- /C below the System 31
- 3.7.1 Watchdog Timer 32
- (Probe Averaging) 37
- /) to speed 39
- 06.0 - 30.5 45
- 007 nop2 52
- 003 loop 52
- 005 sor 005 -sor 52
- 6.8.2 External Compressor On 54
- 6.9.1 Step Numbering 55
- 6.9.3 Control Ports 55
- 7. REMOTE MODE 57
- Setup Commands See Section: 58
- 7.5.4 QC Query Last Command 66
- 7.5.6 DS Disable the SRQ 66
- 7.5.7 PT Read Temperature 67
- /C or /F, as set 68
- 7.6.2 WP Set PID Constants 69
- / over 2 hours and 15 minutes 73
- 7.7.9 QU Quit Controlling 75
- 7.8.1 Status Byte 76
- 7.8.2 Error Byte 77
- 7.8.3 Error/Status String 77
- /C correction 79
- 8. SETUP MODE 81
- term effect 82
- P term effect 82
- /C apart 86
- 9. APPENDIX 89
- /C for 1 hour 93
- /C as quickly as possible 93
- /C for 2 ½ hours 93
- /C for 2 hours & 30 94
- 9.7.4 Noise Immunity 104
- Explicit Program End 105
- Blowers Misbehaving 105
- EIA-232 Problems 106
- GPIB IEEE-488 Problems 106
- COM port issues 107
- Adjusting for changing needs 108
- The Proportional Term 109
- The Integral Term 109
- The Differential Term 110
- /F 3.4, 5.1 111
Související produkty a manuály pro ne Sigma C4
ne Sigma 880 Provozní příručka
(73 stránky)
(73 stránky)
ne Sigma EF-610 - EO-ETTL II Uživatelský manuál
(12 stránky)
(12 stránky)
ne Sigma LENS - Manuál s instrukcemi
(26 stránky)
(26 stránky)
ne Sigma EF-500 DG SUPER Uživatelský manuál
(20 stránky)
(20 stránky)
ne Sigma EF-610 - NA-ITTL Uživatelský manuál
(11 stránky)
(11 stránky)
ne Sigma EM-140 DG EO-ETTL Uživatelský manuál
(12 stránky)
(12 stránky)
ne Sigma SQC-122c Uživatelská příručka
(64 stránky)
(64 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce