Sigma C4 Uživatelský manuál Strana 118
- Strana / 120
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
118
C4 Manual Rev 7.5.2
RS, RSA - Request status byte ........................................ 61
RS-232
See EIA-232 .................................................... 10
Run Time Pre-read Errors ........................................... 49
Invalid Loop Count Error ......................................... 50
No Probe 2 Error ................................................ 50
Setpoint Out of Range Error ....................................... 50
SC Set probe correction.............................................. 66
SD Set UUT temperature differential limits ............................ 69
Serial number display............................................... 24
Serial port ..................................................... 10, 55
Settings ....................................................... 79
Servicing considerations - service WARNINGS.......................... 101
Setpoint
Displaying/changing in local mode .................................. 40
Setpoint error ..................................................... 41
Setpoint Out of Range Error.......................................... 50
Setup mode .................................................... 10, 79
Setup parameter integrity checking.................................... 32
Setup parameters
Autostart mode .............................................. 80, 82
Blower shut-off mode.......................................... 80, 83
Chamber/platform operating limits ................................. 81
Changing values ................................................ 82
Display ........................................................ 81
EEPROM values ................................................ 66
EIA-232 settings ................................................ 79
GPIB address ................................................... 79
Modifying ................................................... 66, 79
Modifying temporarily in remote mode .............................. 66
Number of probes............................................. 79, 82
Permanent changes to in remote mode............................... 66
PID constants............................................. 79, 80, 83
Probe correction (software probe calibration)....................... 80, 83
REFER key enable/disable ........................................ 80
Remote communication port select .................................. 79
Restoring to default values ........................................ 27
SC Set probe correction ........................................... 66
SRAM values ................................................... 66
Temperature scale (
/C or /F) ....................................... 80
UP Write current parameters to NV memory ......................... 69
UP command ................................................... 66
UUT operating differential limits ................................... 81
UUT operating limits............................................. 81
- SIGMA SYSTEMS 1
- MODELS C4 & CC-3 1
- TABLE OF CONTENTS 3
- 1. INTRODUCTION 9
- C4 Manual Rev 7.5.2 10
- 1.5.3 Firmware Uploads 13
- ***-**** 19
- 2.1.3 Mode Switch 20
- 200 - 100c 392 - 148f 23
- 4-0 3276 24
- Starting the upload on the C4 27
- /C below the System 31
- 3.7.1 Watchdog Timer 32
- (Probe Averaging) 37
- /) to speed 39
- 06.0 - 30.5 45
- 007 nop2 52
- 003 loop 52
- 005 sor 005 -sor 52
- 6.8.2 External Compressor On 54
- 6.9.1 Step Numbering 55
- 6.9.3 Control Ports 55
- 7. REMOTE MODE 57
- Setup Commands See Section: 58
- 7.5.4 QC Query Last Command 66
- 7.5.6 DS Disable the SRQ 66
- 7.5.7 PT Read Temperature 67
- /C or /F, as set 68
- 7.6.2 WP Set PID Constants 69
- / over 2 hours and 15 minutes 73
- 7.7.9 QU Quit Controlling 75
- 7.8.1 Status Byte 76
- 7.8.2 Error Byte 77
- 7.8.3 Error/Status String 77
- /C correction 79
- 8. SETUP MODE 81
- term effect 82
- P term effect 82
- /C apart 86
- 9. APPENDIX 89
- /C for 1 hour 93
- /C as quickly as possible 93
- /C for 2 ½ hours 93
- /C for 2 hours & 30 94
- 9.7.4 Noise Immunity 104
- Explicit Program End 105
- Blowers Misbehaving 105
- EIA-232 Problems 106
- GPIB IEEE-488 Problems 106
- COM port issues 107
- Adjusting for changing needs 108
- The Proportional Term 109
- The Integral Term 109
- The Differential Term 110
- /F 3.4, 5.1 111
Související produkty a manuály pro ne Sigma C4
ne Sigma 880 Provozní příručka
(73 stránky)
(73 stránky)
ne Sigma EF-610 - EO-ETTL II Uživatelský manuál
(12 stránky)
(12 stránky)
ne Sigma LENS - Manuál s instrukcemi
(26 stránky)
(26 stránky)
ne Sigma EF-500 DG SUPER Uživatelský manuál
(20 stránky)
(20 stránky)
ne Sigma EF-610 - NA-ITTL Uživatelský manuál
(11 stránky)
(11 stránky)
ne Sigma EM-140 DG EO-ETTL Uživatelský manuál
(12 stránky)
(12 stránky)
ne Sigma SQC-122c Uživatelská příručka
(64 stránky)
(64 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.391 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce